Reset DStv remote
Hold down both the ARC and Standby for about 3 seconds. During this step, the remote lights should change to amber.Continue holding the ARC button as you release the Standby.While you are still pressing the ARC button, dial 9499. Now, release the ARC button to complete the reset process.
Where is standby button on Explora remote?
The standby button on your remote is the power button. It is the button with the power icon and you can find it at the top of the DStv remote.
How do I set my DStv remote to turn off my TV?
To control your TV Press ARC plus VOL+ for more than 3 seconds The LED will give 2 short RED blinks. The VOL+, VOL- and MUTE buttons are now configured for your TV.
Why is my decoder not responding to my remote?
You may also need to press the CABLE button at the top of the remote to direct the signal to the receiver and then try a few functions (Guide, Menu/Settings, etc.) to see if it is only certain buttons that do not work. Failing this, you can try resetting your receiver. Unplug your receiver and wait 15 seconds.
Why is my DStv remote light red?
When using the remote : if there is one RED blink, the remote is already in “Standby Relay” or “Volume Relay” mode, but nothing has been programmed to that button, or there is in an error with the programming sequence.
How do I reset my DStv?
So, what is the code to reset DStv? All you need to do is type ‘RESET smartcard number’ and send the SMS to 30333 (for Nigerians). For example, if your smartcard number is 98674523, you will send an SMS with RESET 98674523 to 30333.
How do I reset my Explora remote?
Resetting a DStv Explora remote for DStv PVR
Firstly, press and hold the SHIFT button and wait for the three blinks on the LED. Finally, enter the resetting code 977, and you are done. Your remote is now ready to use.
Why does my DStv remote flash green?
Press the DStv button on the remote. If the green light blinks (below i, BACK or both) the batteries are working. The batteries supplied with this remote should last for approximately 12 months.
How do I reset my DStv Explora A7 remote?
How to Reset a DStv Explora Remote (model A7)
Press STANDBY + OPTION for more than 3 seconds. ( LED gives 2 short red blink)Press 9 (1 short red blink)Press 8 (1 short red blink)Press 1 (2 short red blinks)Then press OK for more than 3 seconds. ( You will get four red blinks)
How do I turn off the orange light on my DStv?
Since the light on DStv decoder comes up when you have an unread notification, the simplest way to fix it is by reading them. Open all these messages one by one and read the important information they have. Once you are done, press the back button on your remote to exit the mail section.
How do I turn off the red light on my DStv decoder?
A common error when the red light comes up is the smart card setup. If you insert your smart card incorrectly, it will bring this indication. All you need to do is remove, dust, and re-insert your smart card. This should fix the problem and if it persists, just reboot the decoder.
Why is my remote not changing channels?
Check the batteries in your remote control. If you do not see at least 1 button lighting up on the remote upon pressing the button, then the batteries may be depleted. Change the batteries in your remote control and retest. Power down your set-top box using the “CBL” button on the remote and then power it back up.
Why is my DStv remote light red?
When using the remote : if there is one RED blink, the remote is already in “Standby Relay” or “Volume Relay” mode, but nothing has been programmed to that button, or there is in an error with the programming sequence.
How do I reset my DStv 2 remote to 1?
To set the remote to mode 1: press and hold the i button for 3 seconds or until you see the green light blink on 1 (below the i button). If the green light blinks below BACK, the remote is in mode 2.